If you own a Polaris Sportsman 500, chances are you perform your own maintenance. Part of that maintenance is changing the oil. Here is a step-by-step guide on how to change the oil in your Polaris Sportsman 500.
1. Park your ATV on a level surface and turn off the engine. Place a drain pan under the engine to catch the used oil.
2. Remove the drain plug with a wrench and allow all of the oil to drain out of the engine into the pan.
3. Replace the drain plug and tighten it securely with a wrench.
4. Fill up the engine with new oil through the fill hole until it reaches the full line on the dipstick. Be sure to use oil that is specifically formulated for use in 4-stroke engines and ATVs .
- Park the machine on a level surface and engage the parking brake
- Place a drain pan under the engine to catch the used oil
- Remove the oil fill cap/dipstick and set it aside
- Locate the oil drain plug on the bottom of the engine (see image)
- Using an appropriate size wrench, remove the oil drain plug and allow all of the used oil to drain into your catch pan
- If you have an older model Sportsman 500 (pre-1998), reinstall and hand-tighten the drain plug before proceeding to step 5b below
- For all other models, install a new O-ring onto the replacement drain plug and then screw it back in by hand until it is snug – DO NOT OVER-TIGHTEN! Use a wrench to finish tightening it to specifications: 22 ft lbs (30 Nm) for pre-2000 models or 44 in lbs (5 Nm) for 2000 and newer models 6
- Wipe off any dirt or debris from around both openings with a clean rag before moving on to Step 7 below… 7
- Pour approximately 3 quarts of fresh, new Polaris ATV 10W40 Oil into opening at left side of engine (where dipstick was removed in Step 2)
- Next, reinsert and hand-tighten your dipstick/oil fill cap
How Do You Change the Oil in a Polaris 500?
If you own a Polaris 500, chances are you will need to change the oil at some point. Here is a step-by-step guide on how to do just that:
1. Park your Polaris 500 on a level surface and engage the parking brake.
Place a drain pan underneath the engine where the oil will drain from.
2. Locate the oil drain plug on the bottom of the engine and remove it with an appropriate wrench or socket. Allow all of the used oil to drain out into the pan.
3. Once all of the used oil has drained, replace the drain plug and tighten it to specifications. Be sure not to over-tighten as this could strip the threads.
How Often Should You Change the Oil in a Polaris Sportsman 500?
How often you should change the oil in a Polaris Sportsman 500 depends on how often you use it and what kind of conditions you ride in. If you use your ATV primarily for recreational riding, then you can probably get away with changing the oil every 50-100 hours of operation. However, if you ride in dusty or muddy conditions, or if you do a lot of hard work with your ATV, then you may need to change the oil more frequently.
Check your owner’s manual for specific recommendations.
How Many Quarts of Oil Does Polaris Sportsman 500 Take?
The Polaris Sportsman 500 takes 4 quarts of oil.
How Do You Change the Oil on a 2010 Polaris Sportsman 500?
Assuming you would like a blog post discussing how to change the oil on a 2010 Polaris Sportsman 500:
It’s always important to keep up with routine maintenance on your ATV or UTV. One of the most important things you can do is regularly changing your oil.
Not only does this help extend the life of your engine, but it also keeps it running clean and helps prevent any build-up of debris or dirt. Here’s a step-by-step guide on how to change the oil in your 2010 Polaris Sportsman 500:
1) Begin by parking your vehicle on a level surface and engage the parking brake.
You’ll also want to make sure that the engine is cool before beginning this process.
2) Next, locate the drain plug on the bottom of the engine. It will be located near the front left side of the vehicle.
3) Using an appropriate wrench, loosen and remove the drain plug. Be careful as hot oil will begin draining out from here. Place a large pan or bucket underneath to catch all of the used oil.
4) Once all of the used oil has drained out, replace and tighten back up the drain plug using your wrench (be careful not to over-tighten).
5) Now it’s time to add new oil into your vehicle! Locate the fill tube, which is located on top of the engine towards The front right side (it will have a yellow cap).
Remove this cap and slowly pour in new oil until it reaches just below The full line on The dipstick (usually around 4 quarts).
How to do an oil change on a Polaris Sportsman 500
Polaris Sportsman 500 Oil Capacity
When it comes to ATVs, there are a lot of different oil capacities out there. For the Polaris Sportsman 500, the oil capacity is 2.5 quarts. This is important to know because you need to make sure that you have enough oil in your vehicle at all times.
If you don’t, it can lead to some serious problems down the road.
It’s always best to check your owner’s manual before adding any fluids to your ATV. This way, you can be sure that you’re doing it correctly and not over or under filling anything.
With the oil capacity being 2.5 quarts for the Polaris Sportsman 500, make sure that you add this amount when changing your oil or topping off your levels.
Polaris Sportsman 500 Oil Type
If you own a Polaris Sportsman 500, it’s important to know what oil type to use in order to keep your ATV running properly. Here is a helpful guide that will tell you everything you need to know about choosing the right oil for your Polaris Sportsman 500.
Polaris recommends using their own brand of oil, which is specifically designed for use in their ATVs.
However, if you prefer to use another brand of oil, any good quality 10W-40 synthetic motor oil will work just fine. Avoid using conventional oils as they can cause deposits and sludge to build up in your engine over time.
When changing your oil, be sure to check the owner’s manual for specific instructions on how often to do so and how much oil is needed.
As a general rule of thumb, it’s best to change your ATV’s oil every 3-4 months or after every 100 hours of use, whichever comes first.
Be sure to dispose of used motor oils responsibly – never pour them down the drain! Many communities have special collection centers where you can take used motor oils and other hazardous materials for safe disposal.
2005 Polaris Sportsman 500 Oil Capacity
The 2005 Polaris Sportsman 500 oil capacity is 4 quarts. This means that you need to add 4 quarts of oil to the engine when changing the oil. The recommended oil type for this engine is 10W-40.
Polaris Sportsman 500 Oil Drain Plug Location
If you’re like most people, you probably don’t think much about your oil drain plug until it’s time to change your oil. But did you know that there are different types of oil drain plugs, and that the location of your drain plug can vary depending on the make and model of your vehicle?
If you have a Polaris Sportsman 500, the oil drain plug is located on the left side of the engine, just below the exhaust manifold.
The best way to locate it is to follow the oil line from the filter housing.
To remove the drain plug, use an 8mm socket or wrench. Be sure to catch any drips in a pan so you don’t make a mess!
Conclusion
If you own a Polaris Sportsman 500, it’s important to know how to change the oil. This process is actually pretty simple and only takes a few minutes. Here’s what you need to do:
1. Park your Sportsman on a level surface and turn off the engine. Place a drain pan underneath the ATV.
2. Locate the oil drain plug on the bottom of the engine (it will be on the left side).
Remove the plug using an adjustable wrench or socket wrench. Allow all of the oil to drain out into the pan.
3. Once all of the oil has drained, replace the drain plug and tighten it securely with a wrench.
4. Now you’ll need to add new oil to your ATV. Check your owner’s manual for specific instructions on how much oil to add, but typically you’ll want to add between 2-3 quarts (0.95-1 liter).
Leave a Reply