How to Change Oil 2011 Subaru Outback?

Assuming you would like instructions on how to change the oil in a 2011 Subaru Outback: 1. Park your vehicle on a level surface and engage the emergency brake. Locate the oil dipstick near the front of the engine bay on the driver’s side.

2. Pull out the dipstick and wipe it clean with a shop rag or paper towel. Reinsert it fully, then remove it again to check your oil level. The dipstick will have two marks indicating “full” and “add”; if your oil is between these, you’re good to go.

If it’s below the “add” mark, top off your oil as needed before proceeding. 3. Place an oil catch pan beneath the drain plug at the bottom of the engine block (look for a large hex head bolt near where the transmission meets the back of the engine). 4. Using a wrench, loosen and remove this drain plug; be prepared for hot oil to come rushing out—have your catch pan ready!

Allow all of the old oil to drain out completely before moving on. 5a) If you have an access panel under your car (usually located near where passengers’ feet would rest), open it up now so that you can more easily reach/see what you’re doing next. 5b) If not, don’t worry—you can still complete this task without one!

Just be extra careful not to over-tighten things when reassembling everything later on, as there isn’t much room to work with from this angle alone. 6) With your catch pan still in place, locate your filter housing (it will be a big round canister with a black cap sporting either a 17mm or 3/8″ socket symbol). There is usually an arrow embossed onto this housing pointing downwards; this indicates which way to unscrew its cap in order for proper drainage later on.

7) Unscrew and remove this cap, then use an old shop rag or paper towel to clean any residual crud off of both its threads and those of the housing itself—this will help ensure that your new seal is effective.

• Park your car on a level surface and turn off the engine
• Lift up the hood and locate the oil dipstick
• Remove it and wipe it clean with a rag
• Insert the dipstick back into the engine, then pull it out again to check the oil level
• The oil should be between the “full” and “low” marks on the dipstick
• If necessary, add more oil to bring the level up to the “full” mark
• Locate the oil drain plug underneath your car (it will have a small wrench symbol next to it)
• Place an oil catch pan under it before loosening and removing the plug with a wrench (be prepared for some hot oil to come out!)
• 6 Let all of the old oil drain out until only dripping remains, then replace/tighten

How Many Quarts of Oil Does a 2011 Subaru Outback Take?

A 2011 Subaru Outback takes 4.5 quarts (4.2 liters) of oil with a filter change.

Where is the Oil Filter on a 2011 Subaru Outback?

Assuming you would like a blog post discussing the location of the oil filter on a 2011 Subaru Outback: The oil filter on a 2011 Subaru Outback is located on the driver’s side of the vehicle. To locate it, first find the oil dipstick – it will be on the passenger’s side of the engine.

Once you’ve found the dipstick, follow it towards the front of the vehicle until you see a small black canister with a metal cap. This is your oil filter.

How Many Quarts of Oil Does a 2011 Subaru Outback 2.5 I Premium Take?

Most cars these days take between 5-8 quarts of oil, but it is best to consult your car’s owner’s manual for the specific amount. That being said, the 2011 Subaru Outback 2.5 I Premium likely takes around 6 quarts of oil. It is always best to use the recommended type of oil that is specified in your car’s owner’s manual.

What Kind of Oil Does a 2011 Subaru Outback 2.5 I Take?

The 2011 Subaru Outback 2.5 I takes 5W-30 synthetic oil.

How to: change the oil in a 2011 Subaru Outback

2011 Subaru Outback Oil Capacity

The 2011 Subaru Outback has a oil capacity of 5.5 quarts with a filter. The manual recommends changing your oil every 7,500 miles or sooner if you frequently drive in stop and go traffic, tow a trailer, or drive in dusty conditions.

2011 Subaru Outback Oil Type

The 2011 Subaru Outback requires 5W-30 synthetic oil. This oil provides superior protection for your engine, especially during cold starts. It also helps improve fuel economy.

2012 Subaru Outback Oil Filter Location

If you’re looking to change the oil in your 2012 Subaru Outback, you’ll need to know where the oil filter is located. The good news is that it’s easy to find and access – it’s right underneath the engine on the driver’s side. Here’s a quick step-by-step guide to help you out:

1. locate the oil drain plug on the bottom of the engine – it will be on the driver’s side and is fairly easy to spot 2. place a pan or container underneath the drain plug to catch any dripping oil 3. use a wrench or socket to loosen and remove the drain plug – be careful not to over tighten it when putting it back on later

4. once the drain plug is removed, allow all of the used oil to drain out into your container 5. replace the drain plug once all of the oil has been drained (again, be careful not to over tighten) 6. Locatetheoilfilter-itwillbesomewhereonthedriver’ssideoftheengine(usuallynearortouchingtheoilpan)

7. using an appropriate size wrench or socket, loosen and removetheoilfilter 8. take noteoftherubbersealandmakesureittransfersoverto thenewfilter 9. applyasmalldabofoiltothe rubbersealbeforescrewingnewfilterinto place

2010 Subaru Outback Oil Drain Plug Location

The 2010 Subaru Outback oil drain plug is located on the bottom of the oil pan. It is a metal plug with a rubber gasket that seals the opening in the pan. The gasket should be replaced when the plug is removed.

Conclusion

Assuming you would like a summary of the blog post titled “How to Change Oil 2011 Subaru Outback”: Subaru recommends that drivers change the oil in their 2011 Outback every 7,500 miles or sooner if the car is used for towing, driving in dusty conditions, or other severe driving habits. The process for changing the oil is relatively simple and can be done in about 30 minutes.

First, gather the supplies you’ll need: an oil filter wrench, a new oil filter, 5 quarts of fresh motor oil (0W-20 synthetic is best), and a funnel. Then locate the black plastic engine cover under your hood; this needs to be removed so you can access the engine’s oil drain plug. Remove the drain plug with your wrench (it may be slightly difficult to break loose), and allow all of the old oil to drain into a catch pan.

Once the old oil has drained out completely, replace the drain plug and snug it up with your wrench until it’s tight. Next locate your car’s oil filter; it should be on the driver’s side of the engine near the bottom (2011 Outbacks have cartridge-style filters that are easy to remove). Use your wrench to unscrew and remove the old filter; then install the new one by screwing it on until it’s hand-tight.

Finally, add fresh motor oil to your car – Subaru recommends using 0W-20 synthetic for best results. Pour slowly so you don’t overfill; stop when you reach just under 4 quarts if you’re using conventional motor oil, or right at 4 quarts if you’re using synthetic. Replace your engine cover, start up your car, and check underhood again after a few minutes to make sure there are no leaks coming from either your drain plug or new filter.