How to Align Oil Pump Shaft With Distributor?




The oil pump shaft must be aligned with the distributor before the engine can be started. There are two ways to do this: 1. With the engine at TDC (top dead center), remove the distributor cap and look at the rotor.

The rotor should be pointing to the #1 cylinder on the distributor cap. If it is not, loosen the hold-down clamp and rotate the distributor until the rotor is pointing to #1. Then, tighten the clamp and install the distributor cap.

2. Remove the oil pump drive gear and align it with the mark onthe oil pump body. Install the drive gear and turn it clockwise until it stops. This will alignthe oil pump shaft withthe distributor.

  • Remove the distributor cap and rotor
  • Unscrew the hold-down clamp bolt and remove the oil pump shaft assembly
  • Clean the inside of the distributor housing to remove any dirt or debris that could prevent the new shaft from seating properly
  • Insert the new oil pump shaft into the distributor housing, making sure that it is properly aligned with the oil pump drive gear
  • Screw in the hold-down clamp bolt to secure the shaft in place

Does the Distributor Turn the Oil Pump?

If your distributor is mounted on the engine, then the oil pump is most likely driven by the crankshaft. The oil pump provides pressurized oil to the bearings and other moving parts in the engine. The distributor may have a drive gear that meshes with a gear on the end of the camshaft, or it may be directly driven by an eccentric on the camshaft.

In either case, as long as the distributor is turning, it will turn the oil pump.

How to Install a 302 Oil Pump Shaft?

If you have a high performance engine with a solid roller camshaft, you will need to install a 302 oil pump shaft. This is not a difficult task, but there are a few things you need to know before you begin. Here are the steps to take to properly install your new 302 oil pump shaft:

1. Remove the old oil pump shaft. This can be done by draining the oil and removing the pan. Then, remove the bolts that hold the oil pump in place and carefully pull it out.

The old shaft can now be removed from the housing. 2. Clean the housing thoroughly before installing the new shaft. Any debris or dirt left behind could damage the new parts.

3. Install the new oil pump shaft into the housing, making sure it is fully seated. Then, replace the bolts that hold it in place and tighten them securely.

How Long is the Oil Pump Drive Shaft on a 302 Ford?

The oil pump drive shaft on a 302 Ford is 6.5″ long. The oil pump itself is located under the timing cover at the front of the engine and is driven by the timing chain. The drive shaft runs through the center of the pump and is connected to the gears inside.

What Size Drive Shaft is on a 351W Oil Pump?

The size of the drive shaft on a 351W oil pump is 3/4 inch. This oil pump is responsible for circulating oil throughout the engine and keeping it lubricated. Without this oil pump, your engine would quickly seize up and fail.

Homemade oil pump alignment for your small block Chevy V8 or 4.3L Vortex V6.

Ford 302 Oil Pump Shaft Install

If you’re working on a Ford 302 engine, one of the things you may need to do is install a new oil pump shaft. This can be a bit tricky, but with careful attention to detail it’s definitely doable. Here are the basic steps:

1. Remove the old oil pump shaft. This will require disassembling the oil pump itself. Once the shaft is removed, clean up any debris in the housing so that the new shaft can be installed smoothly.

2. Install the new oil pump shaft. Be sure to lubricate it generously with motor oil before inserting it into place. It’s also important to make sure that the shaft is properly aligned before tightening down any bolts or screws.

3. Reassemble the oil pump and reinstall it onto the engine block. Make sure all connections are tight and there are no leaks before starting up your engine again. With these steps in mind, installing a new oil pump shaft on your Ford 302 engine should be fairly straightforward.

Just take your time and be careful, and you’ll have it done in no time!

Oil Pump Primer Rod

When it comes to your car’s oil pump, the primer rod is an important part of the system. The primer rod is what helps to prime the oil pump and get the oil flowing through the system. Without the primer rod, your car’s oil pump would not be able to function properly.

If you are having issues with your car’s oil pump, one of the first things that you should check is the primer rod. If the primer rod is damaged or not working properly, it could be causing problems with your oil pump. In some cases, you may be able to replace the primer rod yourself.

However, if you are not comfortable doing this, it is best to take your car to a mechanic and have them handle it for you.

Ford 302 Oil Pump Drive Shaft Size

The oil pump drive shaft on a Ford 302 engine is 1/2 inch in diameter. The overall length of the shaft is 6-1/4 inches. The driven gear on the end of the shaft is 3/4 inch in diameter and has 24 teeth.


If you’re rebuilding an engine that has a distributor, you’ll need to align the distributor’s oil pump shaft with the engine block. It’s a relatively easy process, but it’s important to do it correctly so the engine runs smoothly. To align the oil pump shaft with the distributor, first remove the distributor cap and rotor.

Then, locate the two alignment marks on the side of the block near the oil pump. There will be one mark on the block and one on the oil pump itself. Line up these two marks and insert a drill bit into the hole in the center of the oil pump shaft.

With the drill bit in place, rotate the oil pump until it lines up with the distributor. You’ll know it’s lined up correctly when you can see daylight through all three holes in a row – this means that all three gears are aligned properly. Once everything is lined up, tighten down all ofthe bolts and replacethe distribut or cap and rotor.

About the author

Leave a Reply

Your email address will not be published. Required fields are marked *

Latest Posts

  • What Kind Of Oil To Use For Hydraulic Jack?

    What Kind Of Oil To Use For Hydraulic Jack?

    The best oil to use for a hydraulic jack is a lightweight, high-quality oil. The oil should be designed specifically for hydraulic jacks and should have a good viscosity rating. If you’re like most people, you probably don’t think too much about what kind of oil to use for your hydraulic jack. After all, it’s…

    Read more

  • What Kind of Oil Does a 2003 Toyota Camry Take?

    What Kind of Oil Does a 2003 Toyota Camry Take?

    The 2003 Toyota Camry takes 5W-30 motor oil. If you own a 2003 Toyota Camry, you might be wondering what kind of oil it takes. The answer is actually pretty simple – your car takes synthetic oil. This type of oil is designed to protect your engine and keep it running smoothly, so it’s definitely…

    Read more

  • What Will Happen If I Don’t Use Dexos Oil?

    What Will Happen If I Don’t Use Dexos Oil?

    If you don’t use Dexos oil, your car’s engine may not run as smoothly. The oil helps to lubricate the engine and keep it cool. If the engine isn’t properly lubricated, it can overheat and break down. If you don’t use Dexos oil in your car, it’s likely that nothing will happen. Your car may…

    Read more