The first step is to remove the gas tank. Next, locate the oil tank cover on the left side of the engine. There are four bolts that hold the cover in place.
Remove these bolts and lift off the cover. Inside the oil tank, there is a paper element filter. Inspect this filter and replace it if necessary.
- Locate the two bolts that hold the oil tank cover in place on the Sportster
- Use a socket wrench to remove the bolts
- Lift the oil tank cover off of the motorcycle
How Do I Remove the Oil Tank Cover on My Sportster
If you’re looking to remove the oil tank cover on your Sportster, there are a few things you’ll need to do first. First, make sure that the bike is in a stable and level position. Once you’ve done that, locate the two bolts that hold the cover in place – they’re located at the front of the tank.
Using a socket wrench, loosen and remove these bolts. With the bolts removed, you should now be able to lift the cover off of the tank.
Before removing anything else, take a moment to clean up any dirt or debris that may have accumulated on the cover or around the area.
Once you’ve done that, locate the oil filter (it’s usually located near the back of the engine). Using an oil filter wrench, loosen and remove this component. Be careful when removing it, as hot oil may spill out.
With the filter removed, slowly unscrew and remove the oil drain plug – again being careful of hot oil spilling out.
At this point, all of the old oil should be drained from your Sportster’s system. To add new oil, simply screw in a new drain plug (finger tight only), add fresh oil to fill up your tank (checking your owner’s manual for capacity), then replace and tighten your filter before putting your cover back on (again using those two bolts at front).
Start ‘er up and enjoy!
What are the Steps to Removing the Oil Tank Cover on a Sportster
Assuming you would like a detailed explanation of how to remove the oil tank cover on a Sportster:
1. First, you will need to gather the appropriate tools. You will need an oil catch pan, a 3/8 drive ratchet with an extension, and a 10mm hex socket.
If your Sportster has an aftermarket exhaust installed, you may also need a second person to help support the weight of the tank while you work.
2. Next, locate the two bolts that secure the oil tank cover in place. These are located on either side of the tank, just below the seat.
3. Using your ratchet and extension, loosen (but do not remove) these bolts until they are loose enough to allow the cover to be removed by hand.
4. Carefully remove the oil tank cover, being careful not to drop it or damage any of the surrounding parts. Drain any remaining oil into your catch pan before proceeding further.
5a. If your Sportster is equipped with stock exhaust pipes, proceed to step 6. If your Sportster has aftermarket exhaust pipes installed, skip to step 5b for special instructions.
5b (Aftermarket Exhaust Pipes Only). Have your helper support the weight of the oil tank while you work – this will make it easier to avoid damaging anything when removing and installing the new parts later on down the road..
Using your ratchet and 10mm hex socket, loosen (but do not remove) all four bolts securing each pipe in place at both cylinder heads.. With all four bolts loosened on each pipe, gently wiggle and pull each pipe free from its respective head.
. Set both pipes aside in a safe location where they cannot fall over or become damaged..
6 (All Models). Now that the oil tank is exposed and empty, take a look inside for any build-up of sludge or debris – if present, use a clean rag or shop towelto wipe away as much as possible.. Inspect both gaskets for wear or damage – if either one shows signs of deterioration(cracks,, tears,, etc.), it will need toreplaced before proceeding further.. Take noteof their orientation so that you can installthe new ones correctly later on..
Is It Difficult to Remove the Oil Tank Cover on a Sportster
The oil tank cover on a Sportster is not difficult to remove. You will need to first remove the gas tank and then the battery. After that, you will need to disconnect the wires from the coil and spark plug.
Once all of that is done, you can simply unscrew the four bolts that hold the oil tank in place and remove it.
How To Remove Oil Tank Cover From Harley Sportster
Conclusion
If you’re looking to remove the oil tank cover on your Sportster, there are a few things you’ll need to do. First, you’ll need to remove the seat. Next, you’ll need to locate the two bolts that hold the oil tank cover in place.
Once you’ve found those bolts, simply unscrew them and set the cover aside. Now, before you go any further, make sure that you have a new gasket ready to go. If not, this is something that can be easily picked up at your local hardware store.
With the old gasket out of the way, simply line up the new one and bolt everything back into place. That’s all there is to it!
Leave a Reply