1. Park your vehicle on a level surface and shut off the engine. Place a drip pan underneath the oil filter to catch any leaking oil. 2. Unscrew the oil filter with an oil filter wrench and let the old oil drain into the drip pan. Screw on a new oil filter, being careful not…
The oil pump shaft must be aligned with the distributor before the engine can be started. There are two ways to do this: 1. With the engine at TDC (top dead center), remove the distributor cap and look at the rotor. The rotor should be pointing to the #1 cylinder on the distributor cap. If…
There are a few ways that you can remove oil from your brake pads. One way is to use a paper towel or cloth to wipe the excess oil off of the pad. Another way is to use a brake cleaner spray. You can also remove the pads and clean them with soap and water….
The process for checking the oil on a Harley Davidson motorcycle is as follows: 1. Park the motorcycle on a level surface and turn it off. 2. Place a clean, dry rag over the end of the dipstick (located under the seat) and pull it out. 3. Wipe any oil off of the dipstick with…
If your car’s oil pump needs to be repaired, there are a few things you can do to fix it. First, check the oil level and add more if necessary. Next, check the oil filter and clean or replace it if needed. Finally, check the oil pump itself for any damage or debris that may…
If your oil drain plug gets stripped, don’t worry. There are a few easy ways to remove it. One way is to use a pair of pliers. Just grip the plug tightly and turn it counterclockwise. If the plug is tight, you may need to use a wrench or socket to get it started. Another…
If your brake pads have become contaminated with oil, there are a few steps you can take to clean them. First, try wiping the pads down with a rag soaked in mineral spirits. If that doesn’t work, you can remove the pads and soak them in a solution of water and dish soap for several…
Removing a broken oil dipstick tube might seem tricky, but it’s a task you can handle with the right tools and method. A broken tube can let dirt into your engine, so fixing it quickly is important. In this guide, I’ll show you simple, step-by-step instructions to remove the broken tube safely and efficiently. Whether…
To get water out of ATV oil, you will need to use a water separator. This is a device that will remove the water from the oil by using centrifugal force. How Do You Get Water Out of Engine Oil? If you find water in your engine oil, it’s important to get it out as…
The transmission oil in a Sportster motorcycle should be checked at least once per year, or more often if the bike is ridden frequently or in dusty or wet conditions. To check the oil level, first, warm up the engine by riding the bike for at least 15 minutes. Then remove the dipstick from the…
The first step is to remove the gas tank. Next, locate the oil tank cover on the left side of the engine. There are four bolts that hold the cover in place. Remove these bolts and lift off the cover. Inside the oil tank, there is a paper element filter. Inspect this filter and replace…
The most complete way to drain the oil from your engine is to remove the oil pan. Once the oil pan is removed, you can drain the oil directly into a catch container. Be sure to clean off any dirt or debris that may be on the gasket surface before reinstalling the oil pan. Can…
To flush the engine before oil changing, place a drain pan under the oil drain plug. Then remove the oil drain plug and allow the oil to drain fully. After that, replace the oil drain plug and fill the engine with fresh oil. 4. Run the engine for a few minutes to circulate the new…
To change the oil in your Mazda 6, you will need: -5 quarts of motor oil -an oil filter -a wrench to remove the old filter (usually a 17mm) What Kind of Oil Change Does a Mazda 6 Need? If you own a Mazda 6, you’re probably wondering what kind of oil change it needs….
The process for changing oil in a Mazda CX-5 is as follows: 1. Park the vehicle on level ground and set the emergency brake. 2. Raise the hood and locate the oil fill cap and dipstick. 3. Unscrew the oil fill cap, being careful not to lose it. 4. Using a funnel, pour in the…